Reducirna stiskalna spojka PPSU 63x50 IVAR.VR PPSU – redukcija za cevi ALPEX
Koda: 88463190Podroben opis izdelka
Prehod med dvema dimenzijama cevi
Reducirna spojka IVAR.VR PPSU 63x50 iz sistema IVAR.PRESS zmanjša dimenzijo voda neposredno na trasi – na eni strani se stisne cev Ø 63 mm, na drugi Ø 50 mm (dimenzije cevi 63 x 4,5 / 50 x 4,0 mm). Primerna je za večplastne cevi ALPEX in TURATEC ter cevi PEX v razvodih do radiatorjev, talnem ogrevanju in sanitarnih instalacijah; za stik s pitno vodo ima higienski atest.
Materiali in mere
- ohišje iz polifenilsulfona (PPSU), odporno proti koroziji in oblogam
- stiskalne puše iz nerjavnega jekla AISI 304, O-tesnila iz EPDM
- pozicionirni obroč iz polikarbonata z okenci za kontrolo vstavitve cevi
- vgradna dolžina L1 118 mm, Z1 11 mm, masa 221 g
Stiskanje in montaža
Spoj se stiska radialno s čeljustmi ustreznega premera (profil F), izključno z odobreno stiskalno napravo po IVAR navodilih za spajanje cevi s fitingi IVAR.PRESS. Cev je treba odrezati pravokotno, kalibrirati in posneti robove; nasajanje lahko olajšate z vodo, olja ali drugega maziva ne uporabljajte. Spoj nastane brez odprtega plamena, s tlakom ga je mogoče obremeniti takoj po stiskanju in sme biti vgrajen v tla, jašek ali pod omet.
Tehnični podatki
| Koda | 88463190 |
| Proizvajalec | IVAR |
| Tip | IVAR.VR PPSU |
| Dimenzija | 63x50 mm |
| Cev | 63 x 4,5 / 50 x 4,0 mm (ALPEX, TURATEC, PEX) |
| Najv. delovni tlak | PN 10 |
| Temperaturno območje | +3 °C do +95 °C |
| Material ohišja | PPSU (polifenilsulfon) |
| Stiskalna puša | nerjavno jeklo AISI 304 |
| Tesnjenje | O-tesnilo EPDM |
| Stiskalne čeljusti | profil F |
| Vgradna dolžina L1 | 118 mm |
| Masa | 221 g |
Pogosta vprašanja
Katere cevi poveže reducirna spojka 63x50?
Cev premera 63 mm s cevjo premera 50 mm – večplastni ALPEX in TURATEC ali PEX dimenzij 63 x 4,5 / 50 x 4,0 mm. IVAR navodila ne dovoljujejo kombiniranja sistema s cevmi in fitingi drugih proizvajalcev.
S katerimi čeljustmi se spojka stiska?
Za to dimenzijo IVAR odobrava čeljusti profila F. Stiska se z napravo s seznama združljivosti v navodilih IVAR.PRESS, na primer REMS IVAR.MINI-PRESS ali NOVOPRESS IVAR.ACO.
Ali spoj lahko ostane vgrajen v steno ali tla?
Da, stisnjeni spoji IVAR.PRESS so lahko nedostopni v tleh, jašku in pod ometom. Sistem pa je treba zaščititi pred UV sevanjem in vremenskimi vplivi.
Ali je spojko po stiskanju mogoče ponovno uporabiti?
Ne. Po IVAR navodilih fitinga, ki je bil že enkrat stisnjen, ni dovoljeno ponovno uporabiti.
Dodatni parametri
| Kategorija: | redukcijske spojke press - PPSU |
|---|---|
| Garancija: | 2 leti |
| Teža: | 0.221 kg |
| Vrsta fitinga: | nipel |
| Premer cevi: | 50 mm, 63 mm |
| Material: | plastika |
| Tip priključka: | stiskalni spoj |
| Koda: | 88463190 |
| Proizvajalec: | IVAR |
| Tip: | IVAR.VR PPSU |
| Dimenzija: | 63x50 mm |
| Cev: | 63 x 4,5 / 50 x 4,0 mm (ALPEX, TURATEC, PEX) |
| Najv. delovni tlak: | PN 10 |
| Temperaturno območje: | +3 °C do +95 °C |
| Material ohišja: | PPSU (polifenilsulfon) |
| Stiskalna puša: | nerjavno jeklo AISI 304 |
| Tesnjenje: | O-tesnilo EPDM |
| Stiskalne čeljusti: | profil F |
| Vgradna dolžina L1: | 118 mm |
| Masa: | 221 g |
Ocena izdelka
Bodite prvi, ki bo objavil članek k tej postavki!
Razprava
Bodite prvi, ki bo objavil članek k tej postavki!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.